Skip to main content

Simple Uhf Tv-Line Amplifier Circuit Diagram

Simple Uhf Tv-Line Amplifier Circuit Diagram. This is very best project circuit, This circuit is This circuit offers 10- to 15-dB gain from 400 to 850 MHz and is therefore eminently suitable for situations where the television signal is weak. Moreover, the filters can be adapted to the individual needs of users. Construction is simplicity itself if the ready-made PC board shown on the next page is used. The tracks should be tinned or silvered for optimum performance and long life. The opening at the center of the board is intended to accommodate the transistor. 

 Simple Uhf Tv-Line Amplifier Circuit Diagram

 Simple Uhf Tv-Line Amplifier Circuit Diagram


This device has two emitter pins, both of which should be connected to ground. The drawings show that the board is divided into two by a small piece of tin plate, which should have a small cut-out for the transistor. The input and output terminals are made from small cable clamps and M3 nuts and bolts. One side of disc capacitors C4, C5, C8, and C9 is soldered direct to the board. Input and output capacitors, C1/C2 and C6/C7 respectively are surface-mount types. C1/C2/L1 form an input filter and C6/C7/L2 form an output filter. The value of the capacitors might have to be lowered to 3.9 pF to obtain the correct frequency range. The amplifier can be housed in a watertight case and then mounted near the antenna at the top of the mast (if used). 

The power is obtained from a simple stabilized 12-V supply: a mains adapter with a 78L12 will do nicely. This can be kept indoors, of course. The amplifier can be powered via the coaxial feeder cable, for which purpose a 10- to 100- choke is inserted in the supply line. Calibrating the amplifier is straightforward: set PI to the center of its travel and then adjust it for optimum picture quality. In practice, the collector current of the transistor is then 5 to 15 mA. This may be checked by temporarily replacing jump lead A by one suitable meter. 

PARTS LIST 
Rl, R2 = 1 KOhmhm 
R3 = 2 ki2 
R4 = 470 PI = 5 preset potentiometer 
CI, C2, C6, C7 = 10 pF surface mount 
C3 = 10 -, 35 V C4, 
C8 = 1 nF disc C5, C9 « 1 nF disc 
LI, L2 = air core, 2 turns of 3mm diameter enamelled copper wire 
L3, L4 = 10- choke or 10 turns of 0.2 mm diameter enamelled copper wire on a ferrite bead. 
T1 = 2SC3358.

Comments

Popular posts from this blog

Build a Low Noise And Drift Composite Amp Circuit Diagram

How to Build a Low Noise And Drift Composite Amp Circuit Diagram. This circuit offers the best of both worlds. It can be combined with a low input offset voltage and drift without degrading the overall system`s dynamic performance. 
 Low Noise And Drift Composite Amp Circuit Diagram


Compared to a standalone FET input operational amplifier, the composite amplifier circuit exhibits a 20-fold improvement in voltage offset and drift. In this circuit arrangement, A1 is a highspeed FET input op amp with a closed-loop gain of 100 (the source impedance was arbitrarily chosen to be 100 kfl). A2 is a Super Beta bipolar input op amp. It has good dc characteristics, biFET-level input bias current, and low noise. A2 monitors the voltage at the input of A1 and injects current to Al`s null pins. This forces A1 to have the input properties of a bipolar amplifier while maintaining its bandwidth and low-input-bias-current noise.

High Power Output Amplifier TDA7294

The famous SGS-THOMSON ST Microelectronics has introduced a Hi-Fi DMOS high-power amplifier circuit TDA7294, its sound great taste bile, which due to its internal circuit from input to output are field-effect devices, rounded sound Mild, delicate Rounuan.  However, with its assembly amplifier, only TDA7294 single-output power is only 70 W, BTL access law is 100 W from top to bottom, do not feel that power cushion. The author several tests, used to promote TDA7294-level, direct-drive one to four pairs of high-power transistor parallel, the output of strong currents, the power output of 400 W (mono), and the circuit is simple and no need to debug that can reliably work Basically, the IC has maintained a sound and performance.  Ruzuo The figure below shows, R6 for the feedback resistor, the author of the value in debugging 22 k Ω more appropriate, R6 also decided this circuit gain, the gain value will increase.  Quiescent current depends on the power of R7, R8, when its value…

Full Power Mobile Phone Jammer Circuit Diagram

Full Power Mobile Phone Jammer Circuit Diagram.To day if we are talking about expert Cell phone Jammers we are conversing about this schematic underneath. First off all you should be very very cautious how to use this apparatus. Its completely illegal and so the reason. I post this Circuit is only for educational and testing causes. This type of apparatus is being utilised by security for VIPS, particularly at their limousines to avoid blasting device initiating while the vehicle passes from the goal cell phone-bomb. Off course there are those who use it to make a antic or to make the persons crazy in the rectangle block you are. 
The power of the jammer is currently sufficient to do your thing, but certainly you can place a 30W linear power amp at the RF output and impede a much wider locality. So, Be pleasant individual with that and recall that there are people who may need desperately to obtain or make a call and one of them could be you! And if you can't oppose of functioning …