Skip to main content

Selective timer alarm.


Description.
A timer circuit using IC 4060 is given here. The IC 4060 is a 14 stage binary counter with a built-in oscillator.R2, R7, C1 are the components that determine the frequency of the oscillator and the outputs will become high one after other and only one at a time. The last five outputs are only used here. The high pulses from the outputs are used to trigger the NE555 IC. Here NE555 is wired as a monostable multivibrator.



The buzzer will produce the alarm when the output of IC2 goes high. The duration of the alarm depends on the components C3 and R5.The duration can be adjusted by varying the value of C3.The alarm will automatically turn OFF after the predetermined time. The trigger pin of IC2 will be normally positive. When the Q1 is forward biased by the positive pulse at its base from IC1, the capacitor C2 becomes charged and reduces the voltage at trigger pin of IC2.This triggers the IC.When the capacitor is fully charged the pin 2 becomes again positive.
The maximum duration from timer IC 4060 will be at pin 3. The times decrease by half in the pins 2, 3, 15, and 13 respectively. The timer duration can be varied by varying the capacitor C1.
  
Notes.
  • Use 6V DC for powering the circuit.
  • Assemble the circuit on a good quality PCB.
  • Mount the ICs on holders.
  • The switch S2 can be a single pole five throw rotary switch.
  • The switch S1 can be a push button switch.
  • S1 is used to reset the timer.
  • S2 is used to select the alarm time.
  • R7 can be used for the fine adjustment of alarm time.

Comments

Popular posts from this blog

Build a Low Noise And Drift Composite Amp Circuit Diagram

How to Build a Low Noise And Drift Composite Amp Circuit Diagram. This circuit offers the best of both worlds. It can be combined with a low input offset voltage and drift without degrading the overall system`s dynamic performance. 
 Low Noise And Drift Composite Amp Circuit Diagram


Compared to a standalone FET input operational amplifier, the composite amplifier circuit exhibits a 20-fold improvement in voltage offset and drift. In this circuit arrangement, A1 is a highspeed FET input op amp with a closed-loop gain of 100 (the source impedance was arbitrarily chosen to be 100 kfl). A2 is a Super Beta bipolar input op amp. It has good dc characteristics, biFET-level input bias current, and low noise. A2 monitors the voltage at the input of A1 and injects current to Al`s null pins. This forces A1 to have the input properties of a bipolar amplifier while maintaining its bandwidth and low-input-bias-current noise.

High Power Output Amplifier TDA7294

The famous SGS-THOMSON ST Microelectronics has introduced a Hi-Fi DMOS high-power amplifier circuit TDA7294, its sound great taste bile, which due to its internal circuit from input to output are field-effect devices, rounded sound Mild, delicate Rounuan.  However, with its assembly amplifier, only TDA7294 single-output power is only 70 W, BTL access law is 100 W from top to bottom, do not feel that power cushion. The author several tests, used to promote TDA7294-level, direct-drive one to four pairs of high-power transistor parallel, the output of strong currents, the power output of 400 W (mono), and the circuit is simple and no need to debug that can reliably work Basically, the IC has maintained a sound and performance.  Ruzuo The figure below shows, R6 for the feedback resistor, the author of the value in debugging 22 k Ω more appropriate, R6 also decided this circuit gain, the gain value will increase.  Quiescent current depends on the power of R7, R8, when its value…

Full Power Mobile Phone Jammer Circuit Diagram

Full Power Mobile Phone Jammer Circuit Diagram.To day if we are talking about expert Cell phone Jammers we are conversing about this schematic underneath. First off all you should be very very cautious how to use this apparatus. Its completely illegal and so the reason. I post this Circuit is only for educational and testing causes. This type of apparatus is being utilised by security for VIPS, particularly at their limousines to avoid blasting device initiating while the vehicle passes from the goal cell phone-bomb. Off course there are those who use it to make a antic or to make the persons crazy in the rectangle block you are. 
The power of the jammer is currently sufficient to do your thing, but certainly you can place a 30W linear power amp at the RF output and impede a much wider locality. So, Be pleasant individual with that and recall that there are people who may need desperately to obtain or make a call and one of them could be you! And if you can't oppose of functioning …